Midland County · Texas
Metal Building Contractor in Midland
Veteran-owned steel building construction in Midland, TX — design, engineering, permitting, foundation and erection under one contract.
- BBB Accredited Business — A+ Rating
- ISNetworld A-Rated Contractor
- OSHA 30-Hour Construction Outreach Training
- MBCI Certified Installer — Standing Seam Roof (SSR) Systems
Typical turnkey cost
$60–$150
per sq ft, turnkey
That is the all-in range: foundation, erection, insulation, electrical, doors and permitting. Shell-only advertisements quote $22–$40 per sq ft for the steel alone, and the finished building typically lands three to four times that — which is where most first-time budgets go wrong. Your number depends on size, site and finish level, and we quote it line by line.
What We Build in Midland
Midland demand is energy, and it is not the shop-and-storage work that drives most Texas metal building markets. What gets asked for here are operations and maintenance facilities, control and SCADA buildings, equipment and maintenance bays, and service structures for oilfield and renewable operators — buildings that have to house instrumentation and staff on remote sites, not just cover equipment. The Permian's solar buildout has added a second stream of the same requirement.
Midland is roughly five hours from our Richardson office. We work the Permian regularly and mobilize on a project basis, with the travel cost stated as its own line rather than folded into the square-foot rate.
Completed in the Permian
One O&M Floor Plan, Built Across the Permian
Built for WHC Energy Services at Greater Bryant Solar here in Midland County: not a shell, but a working facility housing control instrumentation and staff on a remote site. The same floor plan was delivered again at Delaware Ranch Solar in Culberson County, and two more WHC facilities have since been delivered in Hillsboro and Houston. The repeatability is the point, because a second building that matches the first is a different promise from a second building that merely resembles it.
- Full SCADA room
- Two offices
- Restroom
- Maintenance bays
- Standing-seam roof
- Separate pump house for water
- Caliche pad and site work
Culberson County — Delaware Ranch Solar
Midland County — exterior underway
Permitting & Code in Midland
Who issues the permit
Permits are issued by the City of Midland through its Code Administration Division, which handles plan review for commercial work. Midland requires a contractor to be licensed, bonded and registered with the city before a permit will be issued — a prerequisite rather than a formality, and one that adds days for an out-of-town builder who leaves it to the end. Sites outside the city limits are reviewed by Midland County.
Which code applies
Confirm the current adopted edition with the City of Midland before design. Midland's adoption history runs behind the metros — it has operated on materially older editions than Dallas or Austin — and the city's own Building Codes page is the authoritative source rather than any summary, including this one.
What drives the engineering
Two things drive Permian design. Wind exposure is the first: these are open, flat, unobstructed sites, and exposure category frequently governs more than the wind speed itself, which is determined site-specifically under ASCE 7. The second is that these buildings are rarely empty shells. An O&M or control building carries conditioned space, instrumentation, power quality requirements and often a restroom on a site with no municipal water or sewer — so the mechanical, electrical and civil scope is a larger share of the number here than on a comparable shop elsewhere.
Code and permitting details verified 2026-09-07 against City of Midland — Building Codes. Adopted editions change — confirm current requirements with the authority before relying on this for design.
Midland Metal Building Questions
Yes. We delivered an operations and maintenance facility for WHC Energy Services at Greater Bryant Solar in Midland County, containing a full SCADA room, offices, a restroom and maintenance bays, and the same floor plan at Delaware Ranch Solar in Culberson County. WHC facilities in Hillsboro and Houston have since been delivered, and two more O&M facilities are in progress.
Your contractor does. The City of Midland requires a contractor to be licensed, bonded and registered with the city before a commercial permit will be issued. It is routine but it is a prerequisite, and leaving it until the permit application is ready is a common way for an out-of-town builder to lose several days. Sites outside the city limits fall to Midland County instead.
The shell is the smallest part of it. An operations and maintenance building carries conditioned space, instrumentation, power quality requirements, and frequently a restroom on a site with no municipal water or sewer. The mechanical, electrical and civil scope is a much larger share of the cost than on a comparable storage or shop building, and a square-foot rate borrowed from one will not price the other.
Confirm the current adopted edition with the City of Midland before design. Midland's adoption history runs behind the major metros and has sat on materially older editions than Dallas or Austin, so an assumption carried from a DFW project is unsafe here. The city's Building Codes page is the authoritative source.
Metal buildings in other cities
Pricing a Metal Building in Midland?
Tell us the size, the use and the site. You get a line-item estimate that separates the building, the foundation, the site work and the permitting, so you can see what you are actually paying for.